Indesit Washer IWE 6125 User Manual

Instructions for use

WASHING MACHINE

Contents

Installation, 2-3

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

English,1

Polski,13

Technical data

Description of the washing machine, 4-5

Control panel

Display

Running a wash cycle, 6

Wash cycles and options, 7

Table of wash cycles

Wash options

Detergents and laundry, 8

Detergent dispenser drawer

Preparing the laundry

IWE 6125

Special wash cycles

Load balancing system

Precautions and tips, 9

General safety

Disposal

Opening the porthole door manually

Care and maintenance, 10

Cutting off the water or electricity supply

Cleaning the washing machine

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Troubleshooting, 11

Service, 12

Connecting the drain hose

! Do not use extension cords or multiple sockets.

! The cable should not be bent or compressed.

Connect the drain hose,

without bending it, to a

drainage duct or a wall

drain located at a height

between 65 and 100 cm

from the floor;

! The power supply cable must only be replaced by

authorised technicians.

65 - 100 cm

Warning! The company shall not be held responsible

in the event that these regulations are not respected.

The first wash cycle

alternatively, rest it on

the side of a washbasin

or bathtub, fastening the

duct supplied to the tap

(see figure). The free end

of the hose should not

be underwater.

Once the appliance has been installed, and before

you use it for the first time, run a wash cycle with

detergent and no laundry, using the wash cycle 2.

! We advise against the use of hose extensions; if it is

absolutely necessary, the extension must have the

same diameter as the original hose and must not

exceed 150 cm in length.

Technical data

Electrical connections

Model

IWE 6125

Before plugging the appliance into the electricity

socket, make sure that:

width 59.5 cm

height 85 cm

depth 53,5 cm

Dimensions

Capacity

• the socket is earthed and complies with all

applicable laws;

from 1 to 6 kg

Electrical

please refer to the technical data

plate fixed to the machine

• the socket is able to withstand the maximum power

load of the appliance as indicated in the Technical

data table (see opposite);

connections

maximum pressure 1 MPa (10 bar)

minimum pressure 0.05 MPa (0.5 bar)

drum capacity 52 litres

Water connections

Spin speed

• the power supply voltage falls within the values

indicated in the Technical data table (see opposite);

up to 1200 rotations per minute

• the socket is compatible with the plug of the

washing machine. If this is not the case, replace

the socket or the plug.

Energy rated

programmes

according to

regulation

programme 2; temperature 60°C;

using a load of 6 kg.

EN 60456

! The washing machine must not be installed

outdoors, even in covered areas. It is extremely

dangerous to leave the appliance exposed to rain,

storms and other weather conditions.

This appliance conforms to the

following EC Directives:

- 89/336/EEC dated 03/05/89

(Electromagnetic Compatibility) and

subsequent modifications

- 2002/96/EC

! When the washing machine has been installed, the

electricity socket must be within easy reach.

- 2006/95/EC (Low Voltage)

Description of the washing

machine

Control panel

OPTION

buttons with

indicator lights

TEMPERATURE

Button

ON/OFF

button

START/PAUSE

button with indicator light

DISPLAY

Detergent dispenser drawer

DELAYED

START Button

SPIN SPEED

Button

WASH CYCLE

knob

Detergent dispenser drawer: used to dispense

detergents and washing additives (see “Detergents

and laundry”).

DELAYED START button

: press to set a delayed

start time for the selected wash cycle. The delay time

will be shown on the display.

ON/OFF button : press this briefly to switch the

machine on or off. The START/PAUSE indicator light,

which flashes slowly in a green colour shows that the

machine is switched on. To switch off the washing

machine during the wash cycle, press and hold the

button for approximately 2 seconds; if the button is

pressed briefly or accidentally the machine will not

switch off. If the machine is switched off during a

wash cycle, this wash cycle will be cancelled.

START/PAUSE button

with indicator light: when

the green indicator light flashes slowly, press the

button to start a wash cycle. Once the cycle has

begun the indicator light will remain lit in a fixed

manner. To pause the wash cycle, press the button

again; the indicator light will flash in an orange colour.

If the symbol

is not illuminated, the door may be

opened. To start the wash cycle from the point at

which it was interrupted, press the button again.

WASH CYCLE knob: used to set the desired wash

cycle (see "Table of wash cycles").

Standby mode

This washing machine, in compliance with new

energy saving regulations, is fitted with an automatic

standby system which is enabled after a few minutes

if no activity is detected. Press the ON-OFF button

briefly and wait for the machine to start up again.

OPTION buttons with indicator light: used to select

the available options. The indicator light corresponding

to the selected option will remain lit.

SPIN button : press to reduce or completely

exclude the spin cycle - the value is indicated on the

display.

TEMPERATURE button : press to decrease or

completely exclude the temperature: the value will be

shown on the display.

Display

The display is useful when programming the machine and provides a great deal of information.

The duration of the available programmes and the remaining time of a running cycle appear in section A; if the

DELAY START option has been set, the countdown to the start of the selected programme will appear. Pressing

the relative button, the machine automatically displays the maximum temperature and spin speed values set for

the selected cycle, or the most recently-used settings if they are compatible with the selected cycle.

The "programme phases" relative to the selected programme and the "programme phase" of the running

programme appear in section B:

Wash

Rinse

Spin

Drain

The icons corresponding to "temperature" , "Programmed start"

to bottom:

and "spin"

appear in section C from top

If the

When a “delayed start” has been set, the

If the symbol lights up, the display will visualise the set "spin" value.

symbol lights up, the display will visualise the set "temperature" value.

symbol lights up.

Door locked symbol

The lit symbol indicates that the door is locked. To prevent any damage, wait until the symbol turns off before

opening the door.

To open the door while a cycle is in progress, press the START/PAUSE button; if the DOOR LOCKED

switched off the door may be opened.

symbol is

Running a wash cycle

1. SWITCH THE MACHINE ON. Press the

button; the START/PAUSE indicator light will flash

slowly in a green colour.

selected will flash and only the second option will be

activated; the indicator light corresponding to the

enabled option will remain lit.

2. LOAD THE LAUNDRY. Open the porthole door.

Load the laundry, making sure you do not exceed

the maximum load value indicated in the table of

programmes on the following page.

! The options may affect the recommended load

value and/or the duration of the cycle.

7. START THE PROGRAMME. Press the START/

PAUSE button. The corresponding indicator light will

become green, remaining lit in a fixed manner, and

the door will be locked (the DOOR LOCKED

3. MEASURE OUT THE DETERGENT. Pull out the

detergent dispenser drawer and pour the detergent

into the relevant compartments as described in

"Detergents and laundry".

symbol

will be on). To change a wash cycle while

it is in progress, pause the washing machine using

the START/PAUSE button (the START/PAUSE

indicator light will flash slowly in an orange colour);

then select the desired cycle and press the START/

PAUSE button again.

To open the door while a cycle is in progress, press

the START/PAUSE button; if the DOOR LOCKED

symbol is switched off the door may be opened.

Press the START/PAUSE button again to restart the

wash cycle from the point at which it was

interrupted.

4. CLOSE THE DOOR.

5. SELECT THE WASH CYCLE. Set the WASH

CYCLE knob to the desired programme; a

temperature and spin speed is set for each wash

cycle; these may be adjusted. The duration of the

cycle will appear on the display.

6. CUSTOMISE THE WASH CYCLE. Use the

relevant buttons:

8. THE END OF THE WASH CYCLE. This will be

Modifying the temperature and/or spin

speed. The machine automatically displays the

maximum temperature and spin speed values set

for the selected cycle, or the most recently-used

settings if they are compatible with the selected

cycle. The temperature can be decreased by

indicated by the text "END" on the display; when

the DOOR LOCKED

symbol switches off the door

may be opened. Open the door, unload the laundry

and switch off the machine.

! If you wish to cancel a cycle which has already

pressing the

setting is reached. The spin speed may be

button, until the cold wash "OFF"

begun, press and hold the button. The cycle will be

stopped and the machine will switch off.

progressively reduced by pressing the

until it is completely excluded (the "OFF" setting). If

these buttons are pressed again, the maximum

values are restored.

button,

Setting a delayed start.

To set a delayed start for the selected programme,

press the corresponding button repeatedly until the

required delay period has been reached. When this

option is enabled, the

symbol lights up on the

display. To remove the delayed start option press

the button until the text "OFF" appears on the

display.

Modifying the cycle settings.

• Press the button to enable the option; the

indicator light corresponding to the button will

switch on.

• Press the button again to disable the option; the

indicator light will switch off.

! If the selected option is not compatible with the

programmed wash cycle, the indicator light will

flash and the option will not be activated.

! If the selected option is not compatible with

another option which has been selected previously,

the indicator light corresponding to the first option

Wash cycles and options

Table of wash cycles

Max. load

(kg)

Detergents

Max. Max.

temp. speed

Cycle

duration

Description of the wash cycle

Fabric

softener

Eco

Time

(°C)

(rpm)

Prewash Wash Bleach

Normal

Daily

Cotton with prewash: extremely soiled whites.

Cotton: extremely soiled whites.

90°

60°

40°

60°

40°

60°

40°

1200

800

Cotton (1): heavily soiled whites and resistant colours.

Cotton (2): heavily soiled whites and delicate colours.

Cotton: heavily soiled whites and resistant colours.

Coloured Cottons (3): lightly soiled whites and delicate colours.

Synthetics: heavily soiled resistant colours.

Synthetics: lightly soiled delicate colours.

Special

3,5

2,5

800

Wool: for wool, cashmere, etc.

40°

30°

40°

600

1,5

Silk/Curtains: for garments in silk and viscose, lingerie.

Jeans

800

Express: to refresh lightly soiled garments quickly (not suitable for

wool, silk and clothes which require washing by hand).

Sport

30°

800

1,5

Sport Intensive

Sport Light

30°

600

Max. 2

pairs

Sport Shoes

30°

600

Partial wash cycles

Rinse

Spin

1200

Drain

The information contained in the table is intended as a guide only.

For all Test Institutes:

1) Test wash cycle in compliance with regulation EN 60456: set wash cycle 2 with a temperature of 60°C.

2) Long wash cycle for cottons: set wash cycle 2 with a temperature of 40°C.

3) Short wash cycle for cottons: set wash cycle 4 with a temperature of 40°C.

The use of extra compartment 4 excludes the “Pre-wash”

option.

Wash options

! It cannot be used with the 1, 7, 8, 9, 10, 11, 12, 13,

programmes.

Selecting this option enables you to suitably adjust drum

rotation, temperature and water to a reduced load of lightly

soiled cotton and synthetic fabrics (refer to the "Table of

Extra rinse

wash cycles"). “

” enables you to wash in less time

By selecting this option, the efficiency of the rinse is

increased and optimal detergent removal is guaranteed. It

is particularly useful for sensitive skin.

thereby saving water and electricity. We suggest using a

liquid detergent suitably measured out to the load quantity.

! It cannot be used with the 1, 2, 7, 8, 9, 10, 11, 12, 13,

! It cannot be used in conjunction with the 10,

programmes.

Stain removal

Easy iron

This option is particularly useful for the removal of stubborn

stains. Place extra compartment 4 (supplied) into

compartment 1.

By selecting this function, the wash and spin cycles will be

modified in order to reduce the formation of creases. At

the end of the cycle the washing machine will perform slow

rotations of the drum; the indicator lights for the EASY

IRON and START/PAUSE options will flash (the first one

green, the second orange).

When pouring in the bleach, be

careful not to exceed the "max"

level marked on the central

pivot (see figure).

To end the cycle, press the START/PAUSE button or the

EASY IRON button.

To run the bleach cycle on its

own, pour the bleach into extra

For the 8 wash cycle, the machine will end the cycle while

the laundry is soaking and the EASY IRON and START/

PAUSE indicator lights will flash. To drain the water so that

the laundry may be removed, press the START/PAUSE

button or the EASY IRON button.

compartment 4, set the "Rinse"

programme and activate the

"Stain removal" option.

To bleach during a wash

cycle, pour in the detergent

! This function may not be used in conjunction with wash

cycles 7, 10, 11, 12, 13,

and any fabric softener you

wish to use, set the desired wash cycle and enable the

"Stain removal"

option.

Detergents and laundry

Detergent dispenser drawer

Silk: use special wash cycle 8 to wash all silk

garments. We recommend the use of special

detergent which has been designed to wash delicate

clothes.

Good washing results also depend on the correct

dose of detergent: adding too much detergent will not

necessarily result in a more efficient wash, and may in

fact cause build up on the inside of your appliance

and contribute to environmental pollution.

Curtains: fold curtains and place them in a pillow

case or mesh bag. Use wash cycle 8.

Jeans: Turn garments inside-out before washing and

use a liquid detergent. Use programme 9.

Express: this wash cycle was designed to wash

lightly soiled garments quickly: it lasts just 15 minutes

and therefore saves both energy and time. By

selecting this wash cycle (10 at 30°C), it is possible to

wash different fabrics together (except for wool and

silk items), with a maximum load of 1,5 kg.

Sport Intensive (wash cycle 11): is for washing

lightly soiled sports clothing fabrics (tracksuits, shorts,

etc.); for best results, we recommend not exceeding

the maximum load indicated in the "Table of wash

cycles". We recommend using a liquid detergent and

dosage suitable for a half-load.

! Do not use hand washing detergents because these

create too much foam.

Open the detergent

dispenser drawer and

pour in the detergent or

washing additive, as

follows.

compartment 1: Pre-wash detergent (powder)

Before pouring in the detergent, make sure that extra

compartment 4 has been removed.

Sport Light (wash cycle 12): is for washing lightly

soiled sports clothing fabrics (tracksuits, shorts, etc.);

for best results, we recommend not exceeding the

maximum load indicated in the "Table of wash

cycles". We recommend using a liquid detergent and

dosage suitable for a half-load.

compartment 2: Detergent for the wash cycle

(powder or liquid)

Liquid detergent should only be poured in immediately

prior to the start of the wash cycle.

Sport Shoes (wash cycle 13): is for washing sports

shoes; for best results, do not wash more than 2

pairs simultaneously.

compartment 3: Additives (fabric softeners, etc.)

The fabric softener should not overflow the grid.

extra compartment 4: Bleach

Preparing the laundry

Load balancing system

Before every spin cycle, to avoid excessive vibrations

and to distribute the load in a uniform manner, the

drum rotates continuously at a speed which is slightly

greater than the washing rotation speed. If, after

several attempts, the load is not balanced correctly,

the machine spins at a reduced spin speed. If the

load is excessively unbalanced, the washing machine

performs the distribution process instead of spinning.

To encourage improved load distribution and balance,

we recommend small and large garments are mixed

in the load.

• Divide the laundry according to:

- the type of fabric/the symbol on the label

- the colours: separate coloured garments from whites.

• Empty all garment pockets and check the buttons.

• Do not exceed the listed values, which refer to the

weight of the laundry when dry:

Durable fabrics: max. 6 kg

Synthetic fabrics: max. 2,5 kg

Delicate fabrics: max. 2 kg

Wool: max. 1,5 kg

Silk: max. 1 kg

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1200 g

1 towel 150-250 g

Special wash cycles

Wool: all wool garments can be washed using

programme 7, even those carrying the "hand-wash

only"

label. For best results, use special

detergents and do not exceed 1,5 kg of laundry.

Precautions and tips

! This washing machine was designed and

Opening the porthole door manually

constructed in accordance with international safety

regulations. The following information is provided for

safety reasons and must therefore be read carefully.

In the event that it is not possible to open the

porthole door due to a powercut, and if you wish to

remove the laundry, proceed as follows:

General safety

1. remove the plug from

the electrical socket.

• This appliance was designed for domestic use only.

2. make sure the water

level inside the machine is

• The washing machine must only be used by adults, in

accordance with the instructions provided in this manual.

lower than the door

• Do not touch the machine when barefoot or with

wet or damp hands or feet.

opening; if it is not, remove

excess water using the

drain hose, collecting it in a

bucket as indicated in the

figure.

• Do not pull on the power supply cable when

unplugging the appliance from the electricity

socket. Hold the plug and pull.

• Do not open the detergent dispenser drawer while

the machine is in operation.

3. using a screwdriver,

remove the cover panel on

the lower front part of the

washing machine (see

figure).

• Do not touch the drained water as it may reach

extremely high temperatures.

• Never force the porthole door. This could damage

the safety lock mechanism designed to prevent

accidental opening.

• If the appliance breaks down, do not under any

circumstances access the internal mechanisms in

an attempt to repair it yourself.

• Always keep children well away from the appliance

while it is operating.

• The door can become quite hot during the wash cycle.

• If the appliance has to be moved, work in a group

of two or three people and handle it with the utmost

care. Never try to do this alone, because the

appliance is very heavy.

• Before loading laundry into the washing machine,

make sure the drum is empty.

Disposal

• Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

• The European Directive 2002/96/EC on Waste

Electrical and Electronic Equipment, requires that

old household electrical appliances must not be

disposed of in the normal unsorted municipal waste

stream. Old appliances must be collected

separately in order to optimise the recovery and

recycling of the materials they contain and reduce

the impact on human health and the environment.

The crossed out "wheeled bin" symbol on the

product reminds you of your obligation, that when

you dispose of the appliance it must be separately

collected.

4. pull outwards using the tab as indicated in the

figure, until the plastic tie-rod is freed from its stop

position; pull downwards and open the door at the

same time.

5. reposition the panel, making sure the hooks are

securely in place before you push it onto the

appliance.

Consumers should contact their local authority or

retailer for information concerning the correct

disposal of their old appliance.

Care and maintenance

Cutting off the water and electricity

supplies

Cleaning the pump

The washing machine is fitted with a self-cleaning

pump which does not require any maintenance.

Sometimes, small items (such as coins or buttons)

may fall into the pre-chamber which protects the

pump, situated in its bottom part.

• Turn off the water tap after every wash cycle. This

will limit wear on the hydraulic system inside the

washing machine and help to prevent leaks.

• Unplug the washing machine when cleaning it and

during all maintenance work.

! Make sure the wash cycle has finished and unplug

the appliance.

Cleaning the washing machine

To access the pre-chamber:

The outer parts and rubber components of the

appliance can be cleaned using a soft cloth soaked

in lukewarm soapy water. Do not use solvents or

abrasives.

1. using a screwdriver,

remove the cover panel

on the lower front part of

the washing machine

(see figure);

Cleaning the detergent dispenser

drawer

Remove the dispenser

by raising it and pulling it

out (see figure).

Wash it under running

water; this operation

should be repeated

frequently.

2. unscrew the lid by

rotating it anti-clockwise

(see figure): a little water

may trickle out. This is

perfectly normal;

Caring for the door and drum of your

appliance

• Always leave the porthole door ajar in order to

prevent unpleasant odours from forming.

3. clean the inside thoroughly;

4. screw the lid back on;

5. reposition the panel, making sure the hooks are

securely in place before you push it onto the

appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If there are

any cracks, it should be replaced immediately: during

the wash cycles, water pressure is very strong and a

cracked hose could easily split open.

! Never use second-hand hoses.

Troubleshooting

Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”),

make sure that the problem cannot be not solved easily using the following list.

Problem:

Possible causes / Solutions:

The washing machine does not

switch on.

• The appliance is not plugged into the socket fully, or is not making contact.

• There is no power in the house.

The wash cycle does not start.

• The washing machine door is not closed properly.

• The ON/OFF button has not been pressed.

• The START/PAUSE button has not been pressed.

• The water tap has not been opened.

• A delayed start has been set (see “Running a wash cycle”).

The washing machine does not

take in water ("H2O" will flash

on the display).

• The water inlet hose is not connected to the tap.

• The hose is bent.

• The water tap has not been opened.

• There is no water supply in the house.

• The pressure is too low.

• The START/PAUSE button has not been pressed.

The washing machine

continuously takes in and

drains water.

• The drain hose is not fitted at a height between 65 and 100 cm from

the floor (see “Installation”).

• The free end of the hose is under water (see “Installation”).

• The wall drainage system is not fitted with a breather pipe.

If the problem persists even after these checks, turn off the water tap,

switch the appliance off and contact the Assistance Service. If the

dwelling is on one of the upper floors of a building, there may be problems

relating to water drainage, causing the washing machine to fill with water

and drain continuously. Special anti-draining valves are available in shops

and help to avoid this inconvenience.

The washing machine does not

drain or spin.

• The wash cycle does not include draining: some wash cycles require the

drain phase to be started manually.

• The “Easy iron” option has been activated: To complete the wash cycle,

press the START/PAUSE button (see “Wash cycles and options”).

• The drain hose is bent (see “Installation”).

• The drainage duct is clogged.

The washing machine vibrates a

lot during the spin cycle.

• The drum was not unlocked correctly during installation (see “Installation”).

• The washing machine is not level (see “Installation”).

• The washing machine is trapped between cabinets and walls (see “Installation”).

The washing machine leaks.

• The water inlet hose is not screwed on properly (see “Installation”).

• The detergent dispenser drawer is blocked (for cleaning instructions, see “Care

and maintenance”).

• The drain hose is not fixed properly (see “Installation”).

The "option" indicator lights and the • Switch off the machine and unplug it, wait for approximately 1 minute

"start/pause" indicator light flash

and an error code appears on the

display (e.g.: F-01, F-..).

and then switch it back on again.

If the problem persists, contact the Technical Assistance Service.

There is too much foam.

• The detergent is not suitable for machine washing (it should display the

text “for washing machines” or “hand and machine wash”, or the like).

• Too much detergent was used.

Service

Before calling for Assistance:

• Check whether you can solve the problem alone (see “Troubleshooting”);

• Restart the programme to check whether the problem has been solved;

• If this is not the case, contact an authorised Technical Assistance Centre using the telephone number

provided on the guarantee certificate.

! Always request the assistance of authorised technicians.

Have the following information to hand:

• the type of problem;

• the appliance model (Mod.);

• the serial number (S/N).

This information can be found on the data plate applied to the rear of the washing machine, and can also

be found on the front of the appliance by opening the door.

Instrukcja obs³ugi

PRALKA

Spis treœci

Instalacja, 14-15

Rozpakowanie i wypoziomowanie

Pod³¹czenia hydrauliczne i elektryczne

Pierwszy cykl prania

Polski

Dane techniczne

Opis pralki, 16-17

Panel sterowania

Wyœwietlacz

W jaki sposób wykonaæ cykl prania, 18

Programy i funkcje, 19

Tabela programów

Funkcje prania

Œrodki pior¹ce i bielizna, 20

Szufladka na œrodki pior¹ce

Przygotowanie bielizny

IWE 6125

Programy specjalne

System równowa¿enia ³adunku

Zalecenia i œrodki ostro¿noœci, 21

Ogólne zasady bezpieczeñstwa

Utylizacja

Rêczne otwieranie okr¹g³ych drzwiczek

Utrzymanie i konserwacja, 22

Od³¹czenie wody i pr¹du elektrycznego

Czyszczenie pralki

Czyszczenie szufladki na œrodki pior¹ce

Konserwacja okr¹g³ych drzwiczek i bêbna

Czyszczenie pompy

Kontrola przewodu doprowadzaj¹cego wodê

Nieprawid³owoœci w dzia³aniu i sposoby

ich usuwania, 23

Serwis Techniczny, 24

Instalacja

! Nale¿y zachowaæ niniejsz¹ ksi¹¿eczkê, aby móc z

niej skorzystaæ w ka¿dej chwili. W przypadku

sprzeda¿y, odst¹pienia lub przeniesienia pralki w inne

miejsce nale¿y zadbaæ o przekazanie instrukcji wraz z

maszyn¹, aby nowy w³aœciciel móg³ zapoznaæ siê z

dzia³aniem urz¹dzenia i z dotycz¹cymi go

ostrze¿eniami.

Staranne wypoziomowanie pralki zapewnia jej

stabilnoœæ i zapobiega wibracjom, ha³asowi oraz

przesuwaniu siê maszyny w czasie pracy. W razie

ustawienia na dywanie lub wyk³adzinie dywanowej

nale¿y tak wyregulowaæ nó¿ki, aby pod pralk¹

pozostawa³a wolna przestrzeñ niezbêdna dla

wentylacji.

! Nale¿y uwa¿nie przeczytaæ instrukcjê obs³ugi:

zawiera ona wa¿ne informacje dotycz¹ce instalacji oraz

w³aœciwego i bezpiecznego u¿ytkowania pralki.

Pod³¹czenia hydrauliczne i elektryczne

Pod³¹czenie przewodu doprowadzaj¹cego wodê

1. Podùàczyã przewód

zasilajàcy poprzez

Rozpakowanie i wypoziomowanie

przykræcenie do zaworu

wody zimnej z koñcówkà

gwintowanà ¾ gas (patrz

rysunek).

Przed pod³¹czeniem

spuszczaæ wodê do

Rozpakowanie

1. Rozpakowaæ pralkê.

2. Sprawdziæ, czy nie dozna³a ona uszkodzeñ w czasie

transportu. W przypadku stwierdzenia uszkodzeñ nie

pod³¹czaæ jej i skontaktowaæ siê ze sprzedawc¹.

momentu, a¿ stanie siê

ona ca³kowicie

3. Odkrêciæ 4 œruby

zabezpieczaj¹ce

przezroczysta.

maszynê na czas

transportu oraz zdj¹æ

gumowy element z

podk³adk¹, znajduj¹cy siê

w tylnej czêœci pralki

(patrz rysunek).

2. Pod³¹czyæ do maszyny

przewód doprowadzaj¹cy

wodê, przykrêcaj¹c go do

odpowiedniego otworu

dop³ywowego,

znajduj¹cego siê w tylnej

czêœci pralki, z prawej

strony u góry

4. Zatkaæ otwory przy pomocy plastikowych zaœlepek,

znajduj¹cych siê w wyposa¿eniu maszyny.

5. Zachowaæ wszystkie czêœci: w razie koniecznoœci

przewiezienia pralki w inne miejsce, powinny one

zostaæ ponownie zamontowane.

(patrz rysunek).

3. Zwróciæ uwagê, aby na przewodzie nie by³o zagiêæ

ani zwê¿eñ.

! Czêœci opakowania nie s¹ zabawkami dla dzieci.

! Ciœnienie wody w kurku powinno mieœciæ siê w

przedziale podanym w tabeli Danych technicznych

(patrz strona obok).

Poziomowanie

1. Ustawiæ pralkê na p³askiej i twardej pod³odze, nie

opieraj¹c jej o œciany, meble itp.

! Jeœli d³ugoœæ przewodu doprowadzaj¹cego wodê jest

niewystarczaj¹ca, nale¿y zwróciæ siê do

specjalistycznego sklepu lub do autoryzowanego

technika.

2. Jeœli pod³oga nie jest

idealnie pozioma, nale¿y

skompensowaæ

! Nigdy nie instalowaæ ju¿ u¿ywanych przewodów.

nierównoœci, odkrêcaj¹c

lub dokrêcaj¹c przednie

nó¿ki (patrz rysunek); k¹t

nachylenia, zmierzony na

górnym blacie pralki nie

powinien przekraczaæ 2°.

! Stosowaæ przewody znajduj¹ce siê w wyposa¿eniu

maszyny.

Pod³¹czenie przewodu odp³ywowego

Pod³¹czyæ przewód

! Nie u¿ywaæ przed³u¿aczy ani rozga³êŸników.

! Przewód nie powinien byæ pozginany ani

odp³ywowy, nie zginaj¹c

go, do rury œciekowej lub

do otworu odp³ywowego w

œcianie, które powinny

znajdowaæ siê na

przygnieciony.

! Przewód zasilania elektrycznego mo¿e byæ

wymieniany wy³¹cznie przez autoryzowanych

techników.

65 - 100 cm

wysokoœci od 65 do 100

cm od pod³ogi;

Uwaga! Producent nie ponosi ¿adnej odpowiedzialnoœci

w przypadku nieprzestrzegania powy¿szych zasad.

Pierwszy cykl prania

ewentualnie oprzeæ go na

brzegu zlewu lub wanny,

przymocowuj¹c do kranu

prowadnik, znajduj¹cy siê

w wyposa¿eniu (patrz

rysunek). Wolny koniec

przewodu odp³ywowego

nie powinien byæ

Po zainstalowaniu pralki, przed przyst¹pieniem do jej

u¿ytkowania, nale¿y wykonaæ jeden cykl prania ze

œrodkiem pior¹cym, ale bez wsadu, nastawiaj¹c

program 2.

zanurzony w wodzie.

! Odradza siê stosowanie przewodów przed³u¿aj¹cych;

jeœli to konieczne, przewód przed³u¿aj¹cy powinien

mieæ tak¹ sam¹ œrednicê jak oryginalny, a jego d³ugoœæ

nie mo¿e przekraczaæ 150 cm.

Dane techniczne

Pod³¹czenie elektryczne

Model

IWE 6125

Przed w³o¿eniem wtyczki do gniazdka elektrycznego

nale¿y siê upewniæ, czy:

szerokoœæ cm 59,5

wysokoœæ cm 85

g³êbokoœæ cm 53,5

Wymiary

Pojemnoœæ

• gniazdko posiada uziemienie i jest zgodne z

obowi¹zuj¹cymi przepisami;

od 1 do 6 kg

• gniazdko jest w stanie wytrzymaæ maksymalne

obci¹¿enie mocy maszyny, wskazane w tabeli

Danych technicznych (patrz obok);

Dane pr¹du

dane techniczne umieszczone s¹ na

tabliczce na maszynie

elektrycznego

Maksymalne ciœnienie 1 MPa (10 barów)

ciœnienie minimalne 0,05 MPa (0,5 barów)

pojemnoœæ bêbna 52 litrów

Dane sieci

• napiêcie zasilania mieœci siê w wartoœciach

wskazanych w tabeli Danych technicznych

(patrz obok);

wodoci¹gowej

Szybkoœæ wirowania

do 1200 obrotów na minutê

• gniazdko pasuje do wtyczki pralki. W przeciwnym

razie nale¿y wymieniæ gniazdko lub wtyczkê.

Programy kontrolne

zgodnie z przepisami

EN 60456

program 2; temperatura 60°C; wykonane

przy 6 kg za³adowanej bielizny.

! Nie nale¿y instalowaæ pralki na otwartym powietrzu,

nawet w os³oniêtym miejscu, gdy¿ wystawienie

urz¹dzenia na dzia³anie deszczu i burz jest bardzo

niebezpieczne.

Urz¹dzenie to zosta³o wyprodukowane

zgodnie z nastêpuj¹cymi przepisami EWG:

- 89/336/CEE z dn. 03/05/89

(o Kompatybilnoœci Elektromagnetycznej)

wraz z kolejnymi zmianami

- 2002/96/CE

! Po zainstalowaniu pralki gniazdko elektryczne

- 2006/95/CE (o Niskim Napiêciu)

powinno byæ ³atwo dostêpne.

Opis pralki

Panel sterowania

Przycisk z

kontrolk¹

START/PAUZA

Przycisk

TEMPERATURY

Przyciski z

kontrolkami

FUNKCJI

Przycisk

W£¥CZANIA/

WY£¥CZANIA

Wyœwietlacz

Przycisk

URUCHOMIENIE

OPÓNIONE

Szufladka na œrodki pior¹ce

Pokrêt³o

PROGRAMÓW

Przycisk

WIROWANIA

Szufladka na œrodki pior¹ce: do dozowania

œrodków pior¹cych i dodatków (patrz „Œrodki pior¹ce

i bielizna”).

Przycisk URUCHOMIENIE OPÓZNIONE

nacisnac w celu ustawienia opóznionego

uruchomienia wybranego programu. Opóznienie

wyswietlone zostanie na ekranie.

Przycisk W£¥CZANIA/WY£¥CZANIA

: nacisn¹æ

krótko przycisk w celu w³¹czenia lub wy³¹czenia

maszyny. Kontrolka START/PAUZA, która pulsuje

powoli w kolorze zielonym wskazuje, ¿e maszyna

jest w³¹czona. W celu wy³¹czenia pralki podczas

prania konieczne jest d³u¿sze przytrzymanie

naciœniêtego przycisku, przez oko³o 2 sek.; krótkie

lub przypadkowe naciœniêcie wystarczy do

Przycisk z kontrolk¹ START/PAUZA

: kiedy

zielona kontrolka pulsuje powoli, nacisn¹æ przycisk

w celu uruchomienia prania. Po uruchomieniu cyklu

kontrolka œwieci w sposób ci¹g³y. W celu wybrania

pauzy w praniu nale¿y nacisn¹æ ponownie przycisk,

kontrolka zacznie pulsowaæ w kolorze

pomarañczowym. Jeœli symbol

nie œwieci siê,

wy³¹czenia maszyny. Wy³¹czenie maszyny podczas

trwaj¹cego prania anuluje program prania.

mo¿na otworzyæ drzwiczki. W celu ponownego

uruchomienia prania od miejsca, w którym zosta³o

przerwane, nale¿y ponownie nacisn¹æ przycisk.

Pokrêt³o PROGRAMÓW: do ustawiania programów.

W czasie trwania programu pokrêt³o pozostaje

nieruchome.

Funkcja stand by

Pralka ta, w mysl nowych norm europejskich

zwiazanych z oszczednoscia elektryczna, posiada

system auto wylaczenia (stand by), który wlacza sie

po kilku minutach nie uzytkowania. Ponownie

lekko wcisnac przycisk ON-OFF i poczekac, az

pralka ponownie wlaczy sie.

Przyciski z kontrolkami FUNKCJI: do wyboru

dostêpnych funkcji. Kontrolka wybranej funkcji

pozostaje zaœwiecona.

Przycisk WIROWANIA

: nacisn¹æ w celu

zmniejszenia lub ca³kowitego wy³¹czenia wirówki –

wartoœæ ukazana zostanie na wyœwietlaczu.

Przycisk TEMPERATURY : nacisn¹æ w celu

zmniejszenia lub ca³kowitego wy³¹czenia

temperatury; wartoœæ zostanie wskazana na

wyœwietlaczu.

Wyœwietlacz

Wyœwietlacz potrzebny jest w celu programowania maszyny i dostarcza wielu informacji.

W sekcji A wyœwietlany jest czas trwania dostêpnych programów oraz - w przypadku uruchomionego cyklu -

czas pozosta³y do jego zakoñczenia; jeœli zosta³ ustawiony URUCHOMIENIE OPÓNIONE, zostanie

wyœwietlony czas brakuj¹cy do w³¹czenia wybranego programu. Ponadto, po naciœniêciu odpowiedniego

przycisku, maszyna automatycznie wyswietla temperature i przewidziane maksymalne wartosci dla

ustawionego programu lub ostatnie wartosci, jesli sa zgodne z wybranym programem.

W sekcji B wyœwietlane s¹ „fazy prania” przewidziane dla wybranego cyklu oraz, jeœli program jest

uruchomiony, aktualna „faza prania”:

Pranie

P³ukanie

Wirowanie

Wydalanie wody

W sekcji C umieszczone s¹, w kolejnoœci od góry do do³u, ikony odnosz¹ce siê do „temperatury” , do

„Zaprogramowanego startu”

i do „wirowania”

Podœwietlony symbol

sygnalizuje, ¿e na wyœwietlaczu wskazana jest ustawiona wartoœæ „temperatury”.

sygnalizuje, ¿e zosta³ ustawiony „URUCHOMIENIE OPÓNIONE”.

sygnalizuje, ¿e na wyœwietlaczu wskazana jest ustawiona wartoœæ „wirowania”.

Symbol zablokowanych drzwiczek

Wlaczony symbol sygnalizuje, ze drzwiczki sa zablokowane. Aby uniknac uszkodzenia pralki, przed

przystapieniem do otwierania drzwiczek pralki nalezy odczekac, az ten symbol zgasnie.

W celu otwarcia drzwiczek w trakcie wykonywania cyklu nale¿y nacisn¹æ przycisk START/PAUZA; jeœli symbol

ZABLOKOWANYCH DRZWICZEK

jest wy³¹czony mo¿liwe bêdzie otwarcie drzwiczek.

W jaki sposób wykonaæ cykl prania

1. W£¥CZENIE MASZYNY. Nacisn¹æ przycisk

zostanie jedynie druga funkcja a kontrolka

uruchomionej funkcji zaœwieci siê.

kontrolka START/PAUZA zacznie powoli pulsowaæ

w kolorze zielonym.